- Three row fluted seed rollers with restrictors for low sowing rates
- Seeding rates from 1kg/ha – 240kg/ha (dependent on seed type)
- Pegged tooth fertiliser rollers
- Fertilising rates up to 320 kg/ha
- Infinitely variable gearbox
- Remote greasing (grain and fertilizer shaft bearings) is standard
The frame provides the strength and the weight required for efficient operation of the coulters in providing a slot in which the Baker Boots can pass with minimal disturbance into existing pasture species.
The three ranks of tynes which provide a tyne spacing on each rank of 450mm gives operators an increased ability to sow into residues from previous pasture or crops. Spring adjustable coulter assemblies, featuring 340mm (13.38″) coulters, are fitted as a single row across the front of the drill. Sowing spacing is 150mm (6″).
Four sizes are available: 13, 16, 19 and 22 sowing rows and in either linkage or trailing.
Infinitely Variable Gearbox
The 8000 Series Drill is equipped with an infinitely variable speed, oil bath gearbox, which allows the operator to select any required rate between 1 kg/ha and 240 kg/ha. The rate adjustment is a simple screw adjustable set-up. Rubber gates allow the drill to also handle very small to large size seeds.
The metering mechanism uses a three row fluted roller for the seed and a peg tooth roller for the fertilizer. The combined seed and fertilizer box has been located to maintain a low profile for the drill, with weight being carried close to the tractor to minimise its effect on tractor stability when sowing in undulating country.
|Model||Sowing Width||Row Spacing|
|8000TK||Trailed Hitch Kit (Approximately 80kg)|
|42329||Hydraulic Coulter Lift Kit – Allows operator to raise or lower coulters ‘on the go’|
|46690||Jackal hectaremeter in lieu of MC300 hectaremeter|
Press Wheel Kits
|46765||10 Row Press Wheel Kit for 8010 Pasture Drill|
|46766||13 Row Press Wheel Kit for 8013 Pasture Drill|
|46767||16 Row Press Wheel Kit for 8016 Pasture Drill|
|46768||19 Row Press Wheel Kit for 8019 Pasture Drill|
|46769||22 Row Press Wheel Kit for 8022 Pasture Drill|
Press wheels are available in Double Walking Wheel and Single Wheel Types. Kits complete including the rear mounting beam.
Rear Mounting Beam Kits
|46760||10 Row Rear Mounting Beam Kit|
|46761||13 Row Rear Mounting Beam Kit|
|46762||16 Row Rear Mounting Beam Kit|
|46763||19 Row Rear Mounting Beam Kit|
|46764||22 Row Rear Mounting Beam Kit|
Kits include 75mm x 75mm mounting beam, attaching arms and hardware.
|Number of Rows||10||13||16||19||22|
|Transport Width||2m (6’7”)||2.4m (7’10”)||2.83m (9’4)||3.28m (10’9”)||3.74m (12’3”)|
|Linkage Attach||Category 2||Category 2||Category 2||Category 2||Category 2|
|Ranks of Tyne||3||3||3||3||3|
|Tyne Type||25mm (1”) Square Coil Tyne||25mm (1”) Square Coil Tyne||25mm (1”) Square Coil Tyne||25mm (1”) Square Coil Tyne||25mm (1”) Square Coil Tyne|
|Points||Cast Baker Points||Cast Baker Points||Cast Baker Points||Cast Baker Points||Cast Baker Points|
|Coulters||Standard 340mm (13.38”)||Standard 340mm (13.38”)||Standard 340mm (13.38”)||Standard 340mm (13.38”)||Standard 340mm (13.38”)|
|Standard wheels||195/70R15C (all sizes)||195/70R15C (all sizes)||195/70R15C (all sizes)||195/70R15C (all sizes)||195/70R15C (all sizes)|
|Hydraulic Equipment||8” stroke cylinder on trailed machines||8” stroke cylinder on trailed machines||8” stroke cylinder on trailed machines||8” stroke cylinder on trailed machines||8” stroke cylinder on trailed machines|
|Electronic Hectare Meter||Standard||Standard||Standard||Standard||Standard|
|Seed Hopper Capacity m3||0.18||0.23||0.29||0.35||0.41|
|Seed (wheat) Kg||142||185||230||280||330|
|Fertiliser Hopper Capacity m3||0.18||0.23||0.29||0.35||0.41|
|Fertiliser (super) Kg||204||265||335||400||470|
Time to renovate?
Renovate your existing pastures to increase the feed density available to your livestock.
Looking for your local Shearer dealer?
Use our locator to find the one nearest you.